PREMIUM cut-off wheels

for rail cutting

High-performance tool for clean and guided freehand cutting of rails. Suitable for all common hand cutting machines. Difficult application conditions such as humidity, cold or extreme temperature fluctuations cannot harm this PREMIUM cut-off wheel. Even in extreme situations, it guarantees clean and bright cutting areas without the need for time-consuming rework. In addition to handheld cut-off machines with gasoline or electric motors, this tool can also be used on powerful stationary machines. Show more Show less

  • The product offers the shortest cutting times with minimal exertion: even with humidity, cold and temperature fluctuations
  • Cleanest surfaces without any discolouration reduce rework and working times
  • Maximum lifetime and stability
  • Also suitable for powerful (over 5 kW) stationary machines

STANDARD cut-off wheels

for rail cutting

Powerful tool for pure and guided freehand cutting of rails. Suitable for all common hand cutting machines. This STANDARD cut-off wheel is an economical solution when it comes to cutting rails using gasoline or electric petrol saws. Applicable in extreme conditions, it combines stability and a very good lifetime with cutting ability and short working hours. Moreover, this tool can be used on powerful stationary machines. Show more Show less

  • The product offers shortened cutting times with minimal exertion: even with humidity, cold and temperature fluctuations
  • Clean surfaces without any discolouration and reduce rework and working times
  • Very good lifetime and stability
  • Also suitable for powerful (over 5 kW) stationary machines

PREMIUM CERABOND X cut-off wheels

for rail cutting

High performance tool for guided freehand cutting of rails. Suitable for hand cutting machines with electric or petrol motor. The new CERABOND X cut-off wheel was specially developed for cutting rails and skilfully defies the most adverse application conditions. The new bond system prevents premature grain break-out, allowing you to achieve incredible standing times with CERABOND X cut-off wheels. High-quality ceramic abrasive grains guarantee maximum aggressiveness over the entire lifetime. Even under extreme application conditions such as humidity, cold and temperature fluctuations, the rail cut-off wheel from Tyrolit offers the shortest cutting times with little effort. Particularly clean and bright cutting areas reduce rework and working hours, thus supporting the most economical work processes. Show more Show less

  • Shortest cutting times and comfortable working with low effort
  • Very long service life and stability
  • Cleanest surfaces without any discolouration reduce rework and working times
  • Best results even with humidity, cold and temperature fluctuations

PREMIUM cut-off wheels

for guided off-hand cutting of rails

High-performance tool for guided freehand cutting of rails. To be used only with appropriate clamping device. If you are looking for an even easier cutting ability and durable cut-off wheel, you will find it in this PREMIUM product. Thanks to the added zirconium aluminium oxide, the tool offers even more performance and aggressiveness. These special rail cut-off wheels may only be used with the appropriate clamping device, attached to the rail, in guided freehand cutting. Never use in pure freehand application. Show more Show less

  • Maximum abrasiveness and lifetime
  • The zirconium aluminium oxide grain gives the wheel especially good cutting ability and improves performance for the operator
  • Reduced load

Secur Rail grinding wheels

for grinding trains

Longer sections of track are ground - for prevention or correction - using trains equipped with up to 96 grinding spindles. Grinding products from TYROLIT areindividually designed for your requirements. Our high-quality grinding tools enhance the surface quality of the rails, helping to reduce noise and extend rail lifetime. Show more Show less

  • Highest surface quality
  • Longest lifetime

PREMIUM rail cut-off wheels with universal bore

for rail cutting

High performance tool for clean and guided freehand cutting of rails. Suitable for all common hand cutting machines. The special feature of this PREMIUM rail cut-off wheel is its integrated reduction bush, which allows it to be used on machines with 20 mm and 25.4 mm mounting. In addition, it is comfortable in application and at the same time enormously easy cutting and durable, even under extreme application conditions. Therefore, it is an ideal tool for the experienced rail professional for efficient cutting using petrol saw. Show more Show less

  • Integrated reduction bush enables use on machines with 20 mm and 25.4 mm spindle
  • Hard specification for increased lifetime and improved cutting performance
  • Cleanest surfaces without any discolouration reduce rework and working times
  • Very comfortable working without great effort